Hitachi 9257254 9258325 final drive for Hitachi ZX200-3 excavator
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
+86 189 289...
+86 189 2896 5241
China
China
Poland, Zebrzydowa
Product Overview
It starts as a feeling an operator can't quite put a name to. On the ZX200‑3, after a summer of back‑to‑back truck loading, the morning warm‑up seems to take a little longer before both tracks bite evenly. The machine drifts a few centimetres to the left crawling across the haul road. By lunchtime, the track frame under the right sprocket is warm to the touch — warmer than it should be after only four truck cycles. That is the travel motor and planetary reducer, references 9257254 and 9258325, telling you it has reached the end of its first life.
These Hitachi Zaxis ‑3 machines are everywhere: 20‑ton workhorses on subdivisions, roadwork and pipeline jobs, each one racking up six‑ or seven‑hour days. The drive inside each track frame takes high‑pressure oil from the main pump and trades speed for torque, turning the sprocket slow enough to drag 20 tons up muddy cut slopes. When the piston block and valve plate wear, pressure leaks internally — one track lags, the housing runs hot, and a whine builds under load. Most crews nurse it for another week, but by then fine steel swarf is already circulating through the travel loop, scoring whatever it touches. This aftermarket unit arrives as one sealed, bench‑run motor‑and‑reducer assembly, so the worn drive lifts out whole and the replacement drops straight back into the original mounting.
Core Advantages
1. A lapped piston group that holds its pressure lap after lap
The cylinder block, piston shoes and valve plate are machined to close running clearance, so high‑pressure oil does not bleed internally through the motor. That is what keeps both tracks biting evenly — no crab‑walk across a trench, no lazy side, no hesitation the instant the bucket crowds the face.
2. Hardened gear stages built for truck‑loading cycles
A day on a ZX200‑3 means dozens of reverses, ramp climbs and loaded pulls. The planetary gear set uses case‑hardened, ground teeth with controlled backlash, so drive torque spreads across several teeth at once instead of hammering a few. The reducer stays quiet rather than developing an early rattle.
3. Fresh sealing that outlasts a full dusty summer
Site work throws dust, clay and pressure‑wash water at the undercarriage. Every shaft and housing joint gets a new lip seal before the drive leaves the shop. That seal integrity is the single biggest difference between a drive that reaches its first rebuild and one that fails before the season turns.
4. One complete unit, one afternoon under the machine
Motor and reduction arrive bolted together and bench‑checked for torque, leakage and noise. The fitter lifts the old drive out and bolts the new one in without matching loose parts on the shop floor. On a machine that earns by the truckload, that turnaround is worth real money.
5. Aftermarket build price for a high‑hour fleet
A Hitachi dealer exchange unit carries a premium that is hard to justify on a ‑3 series past its early years. This aftermarket drive restores full track mobility at a fraction of that cost, with sample supply and batch pricing for workshops running several Zaxis machines.
Manufacturing & Quality Control
Each unit is built from traced, certified materials. Housings are precision‑machined on CMM‑checked fixtures; gear teeth are finish‑ground and case‑hardened to spec; assembly happens under clean conditions. Before packing, every drive runs on a hydraulic stand while output torque, pressure drop and running noise are logged across its speed range. Units that leak, bind or read outside tolerance come apart for rework rather than shipping. The finished assembly is then fogged with preservation oil, its ports are plugged, and it sits on shock‑absorbing dunnage inside a sealed crate for sea and road freight.
Frequently Asked Questions
Q1: How do I tell 9257254 and 9258325 apart?
A: The two numbers cover build variants across the ZX200‑3 run. Read the tag on your existing drive and send the machine serial number — we cross‑check before dispatch so you get the correct one.
Q2: Does this come with the sprocket?
A: The listing is the complete motor and planetary reduction. The sprocket itself usually transfers over from the old drive; if yours is hooked or worn, ask and we will quote a new one at the same time.
Q3: What should the operator do in the first week?
A: Avoid full‑load reversing on steep ramps for the first shift. Light, cycling use lets the new gears and seals seat before the machine goes back to full truck loading. Check the travel oil level after the first day.
Q4: What voids the warranty?
A: Manufacturing and material defects are covered. Damage from contaminated oil, debris sucked into the motor, a stalled track forced into movement, overload, or a botched installation is not. Photograph any arrival damage before uncrating, and contact us before stripping a failed unit.